Ammeters The DL69-2047 is a digital multifunction meter that simultaneously displays the measured AC voltage, AC current and active power separately on the meter. Electrical energy (kWh). Power factor and other electrical parameters. Note Household selection: 80-300V~100A's If you want to measure…
Descripción del producto
Ammeters The DL69-2047 is a digital multifunction meter that simultaneously displays the measured AC voltage, AC current and active power separately on the meter. Electrical energy (kWh). Power factor and other electrical parameters. Note Household selection: 80-300V~100A's If you want to measure ABC/three-phase voltage and current at the same time, you must buy 3 meters, choose 80-300V for three-phase 4-wire/200-450V for three-phase 3-wire Main technical specifications 1. Measurement accuracy: 1% ±2digit 2. Display: voltage display, current display respectively using 4-bit red 0.32-inch LED digital tube, active power, electrical energy (electricity), power factor and other displays using 5-bit, green 0.32-inch LED digital tube. 3. Measuring range: AC voltage: AC80.0-300.0V (or AC200.0-450.0V, to be ticked by the user when ordering) AC current: AC0.00-100.0A, the display resolution is 0.01A when the measurement current is less than 100A, the current display resolution is 0.1A when the measurement current is greater than 100A, the range is automatically converted. Active power: (measuring voltage AC80.0-300.0V) 0.0-30000W (AC200.0-450.0V: 45000W) Electrical energy: 0.000-99999Kwh, automatic decimal point conversion Power factor: 1.000-0.000 4. Measuring speed: approx. 2 times per second 5. External dimension: 79(L)*43(W/H)*48(D)MM 6. Installation size: 76*39MM 7. ( hole diameter 15.5mm) can meet the national standard 21-25 square (mm) standard copper wire through. Usage and wiring 1. Wiring according to the attached wiring diagram, connect the secondary end of the current (green lead) that comes with the instrument to the blue terminal of the instrument and pass the wires of the measuring circuit once through the middle round hole of the current . 2. Connect the voltage measurement leads to the green terminals of the instrument. Then switch on the measuring voltage. Start reading the measurement results. 3. When the power is switched on, the measurement display shows the following functions: voltage (V), current (A), active power (W). When the left button (SAM CK) on the instrument panel is pressed, the active power (W) display of the instrument changes to display electrical energy (kWh) and at the same time to display the power factor (COS). Pressing the button here changes it back to displaying active power (W). Pressing the (SMA CK) button green shows the display function of the digital tube installed in the following display cycle 4. When it is necessary to measure the power (electrical energy) from zero, press the button (SAM CK) to convert the measurement function to the power (electrical energy) measurement function, that is, the instrument display above the 5-digit green LED digital tube display of the right function indicator in the position of Kwh, and then long press and hold the (SAMCK) button for 5 seconds, the power (electrical energy) display of the 5-digit green LED digital tube Press and hold the (SAM CK) button for 5 seconds, then the 5-digit green LED of the energy (kWh) display shows zero, release the (SAM CK) button and the energy (kWh) display starts from zero. 5. The energy (kWh) display has a power failure automatic data saving to you, that is, when the measurement voltage is disconnected or power failure, the meter will automatically save the current energy (kWh) count data, when re-(incoming) connected to the measurement power meter will continue to add up on the saved data. ========== Dimensions : 79*43*48 Accuracy Class : 1%±2digit Measuring Energy Range : 80-450V 0-100A Phase : Three Phase Model Number : DL69-2047 Display Type : Digital Only DIY Supplies : ELECTRICAL Installation Size : 76*39mm Display : LED digital tube Measuring Speed : 2 times per second
